JETI model s.r.o.

MEZON EVO 40 BEC LMR

MEZON EVO 40 BEC LMR
Art. No.:
JME-040-B-LMR

Description

Electronic Speed Controllers

The speed controllers are available in 2 main types; for brushed motors (DC – commutator) and for brushless motors BLDC. Other factors in the selection of the controller are the voltage range of the drive batteries, current demands of the motor, and the  method used to power the receiver and servos. Jeti speed controllers normally provide thermal protection, protection of the battery against low voltage (LVC), and over current protection. BEC (Battery Eliminator Circuit) controllers include an integrated circuit to provide a stabilized power supply to power the receiver and servos. 

Several product lines of electronic speed controllers for versatile use in model hobby. Available are DC controllers as well as AC synchronous speed controllers. You can select from our solutions for airplane models, helicopters, multicopters and boats.

The MEZON EVO controllers are a successor of the previous product line of the MEZON PRO speed controllers.
The main advantages of this series are very effective cooling, complete telemetry, governor and F3A mode.
MEZON EVO controllers have an aluminum box (except LMR types) which helps with efficient cooling.
The setup wizard helps the user intuitively and quickly set up the controller from the JETI Duplex transmitter.
MEZON EVO is a completely universal controller for models of airplanes, helicopters, ships and vehicles for users not only of JETI Duplex transmitters, but also of other RC systems.

LMR (Limited Motor Run) -  the controller is especially designed for lowest possible weight. This series is not in a metal box and is intended primarily for glider models where continuous motor run is limited to a few seconds followed by a cooldown of the controller. The SW of the controller does not limit the running time, it only monitors the maximum temperature to prevent the controller from being destroyed by overheating. It is the pilot's responsibility to ensure a adequate mode of operation.

Features
    • full EX telemetry (voltage, current, capacity, revolution etc.)
    • setup of device through EX Bus communication from JETI Duplex transmitter
    • accurate governor and full support of helicopter models
    • F3A mode for acrobatic planes
    • adjustable brake with back energy recovering into accumulator
    • powerful BEC with adjustable output voltage
    • wide range of supply voltage 2 - 12 Lixx (max. 51V)
    • bidirectional motor run is possible
    • active proportional brake
    • compact dimensions
    • user-friendly wizard for quick setup of the controller ("Quick Setup mode")
    • in "Expert mode" access to all controller programming options

 

Parameters

Box Plastic tube
Weight [g] 75
Dimensions [mm] 26 x 18 x 83
Sustained current [A] 40
Peak current (max 30s) [A] 40
Supply Voltage [V] 6 to 51
Batteries LiXX 2 to 12
Max. Current BEC [A] 15
OPTO (optically separated radio signal from the power management) No
Average Current BEC [A] 15
Peak Current BEC 1s [A] 30
Voltage BEC [V] 5 to 8.4
Telemetry Yes
Operational temperature [°C] -10 to 85
Resistance in conducting state [mΩ] 1.9
Cable crossection (input/output) [mm²] 2.5 / 2.5

Downloads

Instructions for the basic settings of MEZON EVO - Czech

MEZON-EVO-quick-manual-CZ

Instructions for the basic settings of MEZON EVO - Germany

MEZON-EVO-quick-manual-DE

Instructions for the basic settings of MEZON EVO - English

MEZON-EVO-quick-manual-EN

Instructions for the basic settings of MEZON EVO - France

MEZON-EVO-quick-manual-FR

Full manual for MEZON EVO - Czech

Full manual for MEZON EVO - CZ

Full manual for MEZON EVO - English

Full manual for MEZON EVO - EN

Full manual for MEZON EVO - Germany

Full manual for MEZON EVO - DE